Error 734
Error 734 is a Point-to-Point Protocol error, usually associated with workstation connectivity to a internet provider or wide area network connection. The exact error message is "Error 734: The PPP link control protocol was terminated.".
Source of the problem
Error 734 is usually produced due to an error in authentication. Generally the username or password you are using to authenticate for the connection to initiate is incorrect.
Resolving the problem
-
First and foremost, validate that the username and password you are using for the connection are correct. Most passwords are case sensitive, so you may way to re-enter your password and ensure that your caps-lock key is not active.
- If your username and password are correct, you may be passing on your windows domain credentials where you do not want to. Click your "Start" button, select "Connect To", and then click the connection you use for dial-up services. In the dialog that opens, click the "Properties" button. Now click on the "Options" tab. If the checkbox before "Include Windows logon domain" is checked, click it to uncheck it. Then click "OK". Test your PPP connection again.
- In some cases, you are using a secured password for authentication where the remote server does not permit it. To fix this click the "Start" button and select "Connect To". Now select your dial-up connection. In the "Connect" box that appears, click "Properties", then click on the "Security" tab. In the "Security Options" region under the "Validate my identity as follows" section check the "Allow unsecured password" checkbox if it is unchecked. Now click "OK". Retest your PPP connection.
- You may have multi-link negotiation turned on, but are using a single-link connection. To remedy this click "Start" and select "Settings". Now click "Network and Dial-up Connections". Right click your dial-up connection item, and then click "Properties". Click on the "Networking" tab, and select "Settings". If a check appears next to the "Negotiate multi-link for single link connections", click it to uncheck it. Click the "OK" button twice to finish. Test your connection again.
|
|
Comments (10)
Leave a Reply
- Error 678
Error 678 is an error that is reported when a remote system does not respond correctly when an attempt is made to connect to the Internet. The Error 678 message appears as “The remote computer did not respond.” Broadband connections If this error occurs with a broadband connection, it could be because of the following [...]...
- Error 721
Error 721 is a Microsoft error which is encountered after making an unsuccessful attempt to establish a virtual private network (VPN) connection to a corporate network by using a Point-to-Point Tunneling Protocol (PPTP) client. You may even get an error 721 after making an unsuccessful attempt to establish a dial-up connection after upgrading your computer [...]...
- Error Number: 0x800CCC0E
Error Number: 0x800CCC0E occurs in the Microsoft Windows family of operating systems when there is a problem with Microsoft Outlook Express. A conflict with Simple Mail Transfer Protocol (SMTP) servers while using one of the Microsoft Outlook Express programs to read or browse through mail traditionally causes the error. The full text associated with the [...]...
- Error 1603
When installing software that is packaged with the Windows Installer, users may get an error 1603. The actual error message that displays is “error 1603: A fatal error occurred during installation.” There are a few things that cause this to occur. Windows Installer and Encrypted Folders Users cannot install software packaged in the Windows Installer [...]...
- Error 1933
Error 1933 is a Microsoft error that is sometimes generated when your attempt to install Microsoft Project fails. The general text of Error 1933 reads as follows: "Windows files must be installed for your installation to proceed." This issue indicates that the installation process involves functions that the operating system will not allow. How Did [...]...
i m not able to resolve this problem by applying above steps plzzzzzzzzz help me
thanks my problem is resolved thank you very much
Hi,
I am using TATA PHOTON plus for last couple of days and it was worikng fine for 3 days. Then suddenly once it got disconnected and it was showing that ERROR 734. I called the electronic stores from where I purchased the same but they are not able to help me out for those.
I am using windows VISTA for my laptop. Will it be the same instructions which is mentioned for the other OS?
Yup, just follow the instructions above. The only difference is getting to your modem’s settings page, which can be found at Network Sharing Center. If you’re able to find it, just right click on your Modem which you like to connect, then goto Properties. A dialog box will appear and all you got to do is go to Networking Tab. After that goto settings option, then a PPP settings dialog box will be displayed, in that tick mark the third option Negotiate multi-link for single link connections , then Click on ok, then ok.
Hi I’ve been getting this same error but I’ve tried all solutions to deal with the connection and I’ve figured out that its not the connection itself but the modem I’m using… Its a blackberry 8320 and I tried another blackberry ro connecr and it is connecting as normal so what can that problem be??? And how to solve???
hi, i am use internet through a leptop windows 7 via samsung wave 525 mobile bsnl,but couple of days while connecting a message display error 734 os error: ppp link control protocol was terminated.
prob. remains same, its showing the same error 734 ppp …….
pls help me to resolve this prob.
After following all the above steps, still same problem is continuing. Iam using bluetooth dongle to connect internet from Micromax Q3 mobile to PC. Iam using XP sp2.And iam using IDEA Internet connection in my mobile. So Plz solve this problem. Thanq…
Iam getting same error like “Error 734: The PPP link control protocal was terminated”
I’m stuck with the same problem – trying to connect from Win 7 remotely to a Mac server. I get that same error msg. It verifies my user name and password, then says it’s registering the computer on the network, but then gives the error. I’ve done all the above steps with no difference in result. I’ve also tried turning off all firewalls. I can ping the server fine. It’s set up to use MS-CHAP at both ends.
Anyone with other suggestions? Thanks a lot!